Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Don Casillas

Joined on the:

Aug. 11, 2009

Score

1480

Comment(s)

7

Voted question(s)

1

Voted answer(s)

0

Votes up

0

Votes down

1

Votes up received

3

Votes down received

0

Recent Activity

Question(s) asked

8

Answered question(s)

5

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

17/01/2020

 Chevrolet Don Casillas (1480Pts.)

0

EVO-ALL with RF Kit-No heated seats in 2015 Chevy Traverse

EVO-ALL with RFK942, stand-alone install. Heated seats do not turn on when remote started with RF kit or 3x lock, they do work with factory remote start. All tested well below temp. Install manual #59201 lists heated seats as an option. Option is turned on in programming. Are other options or wiring needed to get the heated seats to work?
Login to reply View 1 answer(s)

02/01/2020

 Chevrolet Damion Wint (130Pts.)

0

'13 Cruze, key-to-start, Evo Rs gmt1 installed, used dcryptor, and i went by all the steps, so why doesnt it still work?

Only blue light flash once each time lock button is pressed
Login to reply View 1 answer(s)

15/06/2016

 Ford Don Casillas (1480Pts.)

0

2016 Explorer Police Interceptor

Has anyone done one of these yet? Have 3 coming in, standard keys (no transponder at all) and no factory remotes? Will I even need an EVO-ALL or hardwire aftermarket remote start?
Login to reply View 1 answer(s)

15/12/2014

 Ford kenny johnson (440Pts.)

1

2015 ford explorer police package with S key basic keys

2015 explorer police package, has generic old school S keys do we have a solution for this car? Wanting to do an evo-all with rf kit if possible.
Login to reply View 1 answer(s)

14/01/2014

 Chevrolet Joshua Caughron (190Pts.)

1

2013 Chevy Cruze 1LT Automatic (NOT PUSH BUTTON START)

I have hooked everything up according to the directions, to the best of my knowlege. I did not hook up the brown, blue, or yellow-black, wires. I programmed and I get the point where it does the 10x yellow flashes then it does nothing else. All lights turn off until I remove the key and the blue light stays solid. It does not start. Am I missing something? After this did not work I tried hooking up the three wires, I grounded black-yellow, hooked blue to the pink-black on 20 pin connector, and brown to the grey-green at light control module. I have the Evo-All and the Wire Harness(thar gm1 I believe is what it is called). Please help. Thank You, C
Login to reply View 2 answer(s)

05/01/2014

 Nissan Don Casillas (1480Pts.)

1

Evo-Ride Not Programming In 2003 Nissan Altima

Previous same question never posted to site? Evo-Ride hardware v3 firmware 2.03, hardwired into 2003 Altima with 8 pin immobilizer connector, will not program. Remote starter works fine with key in ignition. All programming steps and LED blinks are good until key is turned on. Red LED goes solid red every time. All immobilizer wiring checked, metered, and confirmed correct in factory service manual. While troubleshooting, I found that pressing the programming button 5x (instead of 4x) then turning the key on, the red LED will blink 10x like it was programmed correctly. But the car will not remote start and the red LED stays on solid even after remote starter shuts down. Repeated programming process, same results. Tried another new Evo-Ride, exact same problem. Can the Evo-Ride be reset or firmware upgraded if needed? Any help will be appreciated. Thanks!
Login to reply View 1 answer(s)

27/11/2013

 Toyota Don Casillas (1480Pts.)

1

Evo-All Not Programming in 2013 Toyota Highlander PTS (not Hybrid)

Using EVo-All (hardware 6, FW 4.18 and is correct per install manual) with Ultrastart remote starter via datalink for 2013 Toyota Highlander push-to-start. Programming is fine up to step #5. While blue LED is blinking, when the programming button is pushed 1 time, the LED's never change to blue AND yellow blinking. Only blue continues to blink. Rechecked wiring and confimed proper CAN-H and CAN-L connections. Have not tried to reverse them as wiring is correct. What can be wrong or what needs to be tested?
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue